Signal Note

Signal Note

WQKX is short-spaced to WIP-FM Sports Radio 94 WIP (licensed to serve Philadelphia, Pennsylvania) as they both operate on the same channel and the cities they are licensed to serve are only about 106 miles apart. The minimum distance between two co-channel Class B FM radio stations according to current FCC rules is 150 miles.

— — — — — —

Signal note

WARM-FM is short-spaced to WPRB (licensed to serve Princeton, New Jersey) as they operate on the same channel and the cities they are licensed to serve are only 112 miles apart. The minimum distance between two Class B stations operating on the same channel according to current FCC rules is 150 miles.

— — — — — —

how do you change the front turn signal bulb on an 1999 audi avant wagon?

You should have the 1 piece headlights on the 99, which means you will probably have to take them out to get to the turn signal. There are just a couple bolts to pull out and it slides right out. The signal then turns needs a quarter turn to come out and there is the bulb.

— — — — — —

Signal lamp

A signal lamp is a semaphore system using a visual signaling device, often Morse code

— — — — — —

Whats the problem here? 1996 chevy turbo diesel?

This is pretty straight-forward. The oil pressure switch is used as a back up system in case your primary system fails, and that's exactly what happened here. The primary signal to the lift pump comes from the fuel pump relay. So in essense if the relay fails, it will get the signal from the oil pressure switch. Two things can be causing this, BAD fuel pump relay. OPEN signal wire from the PCM to the relay ,(telling the relay to switch) I would go with the relay first, (easier and cheaper to replace). the relay is in the underhood fuse box

— — — — — —

One computers internet is faster than the other?

Try to check the signal strenght to see if one is higher than the other. If there are obstacles between the wireless router and the PC or laptop they can decrease wireless signal

— — — — — —

Put a resistor in series between amp and speaker

Cheap class D amplifiers have very poor rejection of power supply noise/ripple. This is fully expected because the output square wave peak IS the power rail so, the trick is to make that power rail as quiet as possible. So, if your output signal is quite small, noise/ripple on the power rails can dominate. A 20 dB volume reduction is about a 4:1 decrease in sound level as perceived by the ear because 10 dB (or 1 bel) is "defined" as the attenuation that halves loudness at 1 kHz. This does not hold true for other audio frequencies but it's a good measure.If your loudness has reduced by 4 then that is an attenuation of 20 dB. If your earphones have an impedance of about 1000 ohm then adding a 10 k resistor will attenuate the signal to 1000/11000 = 0.09 and if you take the log and multiply by 20 you get 20.82 dB

— — — — — —

Low Signal from wireless router. Replace?

Depending on the make up of the home and exactly where they are in relation to each other even a new one may not give you a better signal. The more walls/floors the signal has to travel through the weaker it gets. Even in a entertainment center needs to be taken into account. Some routers allow you to replace the antenna for higher gain antenna. Also the 360 does not support "N" only A, B and G. Another issue is what are the wall/floor materials made of. The wall of my bathroom was made of Durock which has concrete in it and created a wireless deadspot and signals would NOT go through it

— — — — — —

Signal transduction

gp130 has no intrinsic tyrosine kinase activity. Instead, it is phosphorylated on tyrosine residues after complexing with other proteins. The phosphorylation leads to association with JAK/Tyk tyrosine kinases and STAT protein transcription factors. In particular, STAT-3 is activated which leads to the activation of many downstream genes. Other pathways activated include RAS and MAPK signaling

— — — — — —

Unable to connect to open wireless network sometimes in ubuntu 12.04

I would not use monitor mode either, without more information these are the things that I see that may help. Please run:If you insist on using monitor mode please try:that will turn power management off for mon0.It is best to set your router to just wpa2 encryption if you have that option. The signal strength is to low on both networks that you have listed to be able to connect too, but the first set of commands I gave you to run usually helps with that to some extent. You may need to move closer to your router to be able to connect especially if there are walls or something blocking the signal.Your device is ar9285 with linux drivers it has the worst signal strength of all the devices in this series from my experience so you will not be able to get very far from your router no matter what you do.